DC Motors

Product Details:
Mabuchimo Motor DC motor, the same as the stock motor FC280SA-2470. 10,000 rpm, 3 to 4.5v DC. Double shafted. Originally made to operate an electric razor but perfect for any robotic or novelty project. 2 mounting holes on spline. 11.5mm c-c. Shaft dimensions: 2.0mm (0.0787") shaft, 10.6mm (0.417") long one side, 5.5mm (0.218") long spline side. Body measures: 24.2mm x 18.3mm x 30.5mm long. 20,000 available!

Product Details:
Minimotor DC motor. 6 - 9v DC. 1500 rpm. Brass pulley with 1/8" wide groove measures 1/4"W x 3/8"D (0.314" x 0.637" overall). 1-1/2"D x 1.3"L body. Made in Japan.

Product Details:
Applied Motion Products DC motor. 19 ohm.

Motor Specifications:
• Rated for: 9.0vdc @ 0.47 amps
• Holding Torque: 30.5 oz.-in
• Continous Running Torque: 15 oz.-in
• 8 lead, 1.8 deg. step angle, 5% step accuracy, 4 phase winding for hookup in series or parallel.
• Dimensions: Standard square flange; 2-1/4" with (4) holes for mounting x 1-1/2"L.
Shaft: 0.250" dia. x 1.435"L with flat, connection via 3"L leads.

Product Details:
Motorola Seguin DC motor. 12v DC. Brass "V" pulley is 0.533 O.D. on 0.1"D shaft. 1.82" diameter. 1.555" c-c flange mounting holes. Case flange is 1-15/16" x 2". Case is 1-13/32" from front of flange to rear of case. Case is 1-13/16" in diameter. Includes shock mount shielded case. Mfg. P/N: 59C43994C02-C.

Product Details:
DC motor. 12v DC, 20 ma. 1 wire motor tach / gen output. 1.566"D x 1.686"L body. 0.075"D x 0.50"L round shaft. 4" leads. Made in Japan.

Product Details:
Servo Magnetics 15,000 rpm DC brushless motor. Requires external controller to supply DC pulses to windings for rotation.

 

• 12v DC
• Low noise
• Precision long life ball bearings
• Peak torque: 80 oz-in
• Torque constant: 1.65 oz-in / amp
• Shaft: 0.25" x .81"L
• Body: 2.25"D x 2.23"L

Product Details:
Mabuchi Motor Company 12v DC carbon-brush motor. CCW / CW rotation. Tapped mounting holes ISO M3.0 x 0.5, two places. Additional P/N: TD071920.

• Operating range: 4.5 12.0, 12v constant nominal
• No load speed: 24,000 r/min, 1.30 amps
• Maximum efficiency: 20,510 r/min, 7.65a
• Torque: 31.1 mN-m, 317 g-cm
• Output: 66.7
• Stall torque: 214 mN-m, 2,181 g-cm, 45a
• Dimensions: 35.8mm dia. x 50mm long. Geared shaft is 0.32" long

Product Details:
Back in stock! DC motor. 12 - 24v DC. Includes RF Interonics Bay Shore capacitor, 0.22 µF, 100v. 3" diameter body x 3.15" (+ shafts). 5/16" diameter "D" thru-shaft x 5/8" x 1". NSN: 6105-01-127-5200. NOTE: May be marked: B54735-G1.

Product Details:
Canon DC motor made for Canon printers. 18 - 24v DC. 1.61"D x 1.35"H body. 0.178" (2mm) shaft, 9mm long. Four threaded mounting holes on face. Made in Japan. NOTE: This lot has several equivalents, we may substitute a different model number but it will be the same motor as pictured.

Product Details:
Johnson DC motor. 24v DC, 60 ma (no load). 18mm (0.709") x 23.3mm (0.923"), 1.344" overall length. 2mm (0.775") x 9mm (0.368") round fluted shaft. 2 mounting holes on face, 15.5mm c-c. External access to brushes. 30,000+ pcs available!

Product Details:
Mabuchi Motor makes a gutsy little Japanese motor suitable for most remote control jobs. 3v DC, 1" diameter body, 1-5/16" long. Spline shaft 5/64" diameter x 7/16" long. About 1,500 pieces available.

Product Details:
HP replacement motor. High torque. Shaft has 14 point gear 0.37¢ in diameter. 27 mm diameter. 12v DC. 1.08¢ diameter x 1.47¢ body, 2.16¢ length overall with connectors and shaft. Two threaded front mount holes 0.08" diameter, 0.64" c-c each side of shaft. Very reliable. 1,280 available! Alt.
P/N: RD970X19.

Product Details:
DC motor. 8 - 18v DC. Made for 1970's tape decks. 1.54"D x 1.45" body. "V" pulley, 0.06"W x 0.369"D. Two mounting flanges 1.836" c-c.

Product Details:
Matsushita hi-torque motor can surprise you. Draws only 200ma at 13.2v DC, but she rocks! 1-3/8" O.D. x 15/16" deep. 5/64" shaft diameter x 5/16" long. Mounts by 6 threaded holes on face. An excellent replacement motor for vintage automotive cassette tape players.

Product Details:

Dunkermotoren governor controlled permanent magnet DC motor. No load current.

Motor Specifications:
• Rated for: 3 - 30v DC
• Governor control adjustable 2850-3200 rpm
• 20 ma. max. continuous torque 85 PCM
• Stall torque: 5 oz.-in.
• Speed without governor: 20,000 rpm at 350 ma.
• Body dimensions: 1.30" dia. x 3"L
• Shaft dimensions: 0.080" nominal (0.0785) x 0.375"L

Product Details:

TRW Globe Motors DC permanent magnet motor with tachogenerator. Mounts at front tapped holes on 1" center.

• Rated for: 24v DC
• Body Dimensions: 1-1/4" dia. x 2-1/8"L
• Shaft Dimensions: 0.098" dia. x 3/8"L. Pulley pressed on (fits 1/4" wide belt).

Product Details:
Yale dual DC motor. 18 - 24v DC. Made for 1970s tape decks. Belt pulley with set screw on 2mm shaft. 1-1/2"D x 1-3/8".

Product Details:

TRW Globe Motors DC motor.

• Rating: 24v DC, 165 ma., 5500 rpm, no load.
• Stall Torque: 15 oz.-in at 3 amps.
• Torque Constant: 5.5 oz.-in. / amp.
• Armature Resistance: 8.3 ohm
• Body Dimensions: 1-1/2" dia. x 2-5/8"L
• Shaft Dimensions: 0.1562" dia. x 5/16"L with flat. Face mount with four tapped holes

Product Details:
Black & Decker power supply. 16 vdc @ 4 amp nominal. Trimmable 12.6-14 vdc. Front panel control - voltage trim. Output jack - polarized. 6-1/2" x 3-3/4" deep. 3-3/8"H.

• Input: 120 vac, 60 Hz, 0.6 amp

Product Details:
Indiana General DC motor. 60v DC, 11.2 amp, 1,390 rpm, 0.9 HP. Double-ended shafts. New stock.

• Body Dimensions: 4"D x 9"L
• End #1: 1/2" shaft, 1-3/4"L, 2.3" centers on 4 tapped 3/16" mounting holes
• End #2: 0.624" / 0.475"D stepped shaft, 1-1/4"L, shaft is hollow, 3.25" center on 2 tapped 3/16" mounting holes

Product Details:
Pioneer DC motor. Model #CXM-004. 1976 OEM vintage stock. New, unused. CXM models typically used for tape drives.

Product Details:
Globe Industries, USA DC permanent magnet motor. 75v DC, 9,000 - 11,000 rpm. No load; 1.70 (oz. in.) torque max. 6.8 theoretical stall (oz. in), 0.07 max amps no load, 0.29 max rated load amps, 0.85 nominal stall amps. "-16 denotes armature winding." (See ). 2.56"L to tip of shaft, 0.12"D shaft x 1/2"L, 1.20" diameter body. Weight: 5 oz. NSN: 6105-00-001-3680.

Product Details:
Alliance Mfg. Co. DC motor. Reversible. 115v DC @ 0.45 amps. 1/50 HP, 6000 rpm. 3 wires. 2"D x 3"L. 0.370"D spline gear, no tooth. Circa 1952.

Product Details:
Mabuchi tiny toy motor. 5 - 9.6v DC. 17,000 rpm. Carbon brush. Mounts by 2 threaded holes on face, 14mm c-c. 23.88mm D x 34.28mm L (+ shaft). 2m x 10.75mm L shaft.

Product Details:
Motor, 4 terminal contacts, item marked 10v, 15 tooth gear. 2.85" tall x 1.852" length x 1.466" width. Mount by 4 shaft end .96" grid 8-32 threads or 2 rear end 1.293" c-c 8-32 threads. Circa 1956. Cast housing.