Pushbutton Switches - Illuminated

Product Details:
GC pushon-pushoff lampless indicator switch. 2 amp @ 250v. DPDT. Orange indicator when "ON". Up to 5/16" thick panel. Fits 9/16" hole.

Product Details:
GC pushon-pushoff lampless indicator switch. 6 amp @ 250v. DPDT. Switch center turns orange when switched. Fits 9/16" mounting hole.

Product Details:
"Press to Test" pushbutton switch. Lens end has boot / seal washer to hermetically seal. Aircraft style. Lamp (midget bayonet base) NOT included. 3 terminal. Amber lens. 7/16" hole mount. 1-3/4" overall length.

Product Details:
Licon illuminated pushbutton switch. 10 amp. SPDT momentary contact. Requires 15/16" x 11/16" lens with lamp and holder. Fits 13/16" x 1-1/16" hole. 2-1/4" behind. UL listed.

Product Details:
Switchcraft push light "POWER" switch. DPDT maintained. Uses two midget lamps. 1" x 7/8" hole required. 1.8" behind panel depth. NSN: 5930-01-106-7601

Product Details:
Clare Pender lighted aircraft pushbutton switch. "Power On-Off". 4 poles, 2 normally open, 2 normally closed, maintained. 1.42" c-c mounting bracket holes. Includes midget lamp 327 (28v). NSN: 5930-457-4376.

Product Details:
Aircraft push light switch. Lens "NO GO" yellow. DPDT momentary contacts. Requires two midget lamps (not included). 0.76" x 0.75" hole required. 2.4" behind. NSN: 5930-00-150-1094.

Product Details:
Jayel momentary pushbutton switch. SPDT, 7 amp contacts. 0.5" square button with #5 which illuminates when button is pushed. Includes "387" 28v lamp. Mounts in 0.468" diameter hole, 1-3/8" behind panel depth. NSN: 5930-01-293-9981.

Product Details:
Marco-Oak panel lamp socket with threaded base. SPDT, push-on, push-off, "maintained". Includes trim nuts. No lamp or lens. Fits 1/2"D hole. 2" overall length. Harris P/N: 604-0621-00.

Product Details:
Microswitch DPDT micro switch would be a lot nicer if we had the lens and lamp. Uses bayonet midget bulbs. 5/8" hole, 2" behind panel.

Product Details:
General Electric illuminated pushbutton switch. 1/2"D red illuminated button shrouded in guard. SPST. Spade terminals. Accomodates 1/16" - 1/4" panel. 1" above chassis, 2" behind chassis. 6 volt AC - DC lamp. Harris P/N: 604-0611-001.

Product Details:
Molex momentary switch, indicating lens. "LOAD". Lights up with 6v lamp. SPDT, 2 amp, 125 vac contact. Snaps into 0.5" x 1.125" hole. 2-1/4" behind panel depth. Alt. P/N: 100104-002. NSN: 5930-00-567-0958.

Product Details:
Stacoswitch pushbutton switch. Amber button lettered "OW PTT". Uses single midget lamp, NOT included. Maintained DPDT, 3 amp silver contacts. Fits 15/16" x 15/16" hole. NSN: 5930-01-082-3651.

Product Details:
MSC aircraft push light switch. Dual SPDT microswitch. White "Stop" lens. 0.855" x 1.1" x 2.75" behind. Includes 4 midget blue 327 lamps. NSN: 5905-00-145-9779. Full manufacturer's P/N: RF1/10A1SG1W/X7E12STOP.

Product Details:
Control Switch pushbutton switch. 4 poles, 3 SPST, N.O., 1 SPST, N.C. Momentary contact. Made for light bulb & lens cap, (not included). Includes nuts / washer. 0.62" O.D. threads. Up to 0.265" panel thickness. Use with lens covers such as: (SWP) MID-PBL-Y or (SWP) MID-PBL-BL.

Product Details:
Micro 4PDT pushbutton switch. Momentary, 3 amp @ 125 vac. 11/16" square yellow button requires 5/8" hole. 7/8" x 1-1/8". 2-9/16" overall length. 1-1/2" behind panel depth. Button can be illuminated with midget bayonet bulb.

Product Details:
MicroSwitch LED green indicator. 5 vdc, 25 ma. Fits 1/4" x 3/4" hole. No switch.

Product Details:
General Electric "Push to Test" illuminated push button switch. Oil tight, red lens. 6 vac or vdc lamp circuit, 1 normally closed, 1 normally open. 600v contact. Fits 1-3/16" hole.

Product Details:
Omron pushbutton switch requires interchangable lighted colored buttons. 3 amp contact.

Product Details:
Omron push button lens for (SWP) A3A-7320 switch. LED inside button connects to external lugs. Requires series resistor for LED. Red / Orange color. LENS Only!

Product Details:
Omron push button lens for (SWP) A3A-7320 switch. LED inside button connects to external lugs. Requires series resistor for LED. Yellow color. LENS Only!

Product Details:
Molex pushbutton switch. 125 vac, 8-1/2 amps. Normally open. Momentary contact red button illuminates when pressed. Also engages "load" contact. Fits 0.865" x 1.2" hole. Stainless steel bezel measures 1.08" x 1.27", 1.67" behind panel depth. QC or solder terminals.

NOTE: This is a similar replacement fan switch for Jenn-Air cook top model 2375/ERS, which is no longer available from the appliance parts supply houses. It is NOT exact. Momentary N.O. contacts.

Product Details:
Staco pushbutton switch. DPDT, 3 amp contacts. Switch labeled "TERM TAPE". Requires one midget flange bulb (NOT included). Requires 0.80" x 0.80" hole, 2-1/4" deep. NSN: 5930-01-043-5931.

Product Details:
MicroSwitch pushbutton switch has SPDT, 0.1 amp 125 vac / vdc momentary contact. 5 vdc, 25 ma red LED "on" light. Fits 3/4" square hole. 1-3/4" behind panel depth.

Product Details:
MicroSwitch pushbutton switch. SPDT, 125v @ 3 amp, 240v @ 2 amp. Push-on, Push-off. Bezel measures 0.8" x 0.8" overall. 1-3/4" behind panel depth. Lens cap and lamp NOT included. Harris P/N: 604-0891-000.

Product Details:
Eaton Corporation avionic pushbutton switch. DPDT, momentary. Switch labeled "ADC Test". Includes two (2) 327 midget bayonet lamps. 5/8" x 7/8" hole required, 2-1/4" behind. NSN: 5930-01-229-6383.

Product Details:
Aircraft pushbutton switch. DPDT, maintained. Switch labeled "Annunciator". Requires 4 midget flange lamps. Includes blue lamp covers. Fits 0.964" x 1.195" hole. 3" behind panel depth. NSN: 5930-01-189-5307.

Product Details:
Tellite momentary pushbutton switch. Light indicator. Specialty mount. Includes 2 lamps. 7/8" x 5/8" x 2-1/2"L. NSN: 6210-01-025-9676.

Product Details:
Eaton indicator light. Lens labeled "IFF" & "CHALLENGE". NOTE: This is only the top portion of the switch. Micro-switches NOT included. Includes 4 midget lamps. Requires 1.195" x 0.964" hole. NSN: 6210-00-187-4008.

Product Details:
Eaton aircraft push light switch. Lens labeled "POWER SUPPLY TEST". Two SPDT, 2 amp maintained micro switches, push-on, push-off. Fits 1.195" x 0.0965" hole, 3" deep. Includes 4 midget lamps. NSN: 5930-00-107-6162.

Product Details:
Momentary pushbutton switch. Labeled "5 RPM". White lens, turns green when depressed. Includes 4 midget, 28 vdc lamps (green). Fits 0.964" x 1.195" hole. 3.625" behind panel depth. NSN: 5930-00-986-8605.

Product Details:
Aircraft pushbutton switch. Labeled "Ceiling Lts Bright", "Ceiling Lights Dim". DPDT, maintained. Includes 4 blue, 28v midget lamps. 0.855" x 1.1" x 2.97" behind panel depth. NSN: 5930-00-987-1193.

Product Details:
MSC aircraft push light switch. 4 internal midget lamps. 2 SPDT microswitch are momentary. No lens. 1.195" x 0.964"D hole required. NSN: 5930-00-407-4464.

Product Details:
Korry Mfg. momentary aircraft pushbutton lighted switch assembly. Two SPDT micro switches. Two midget lamps per lens. Split lens, "Track" & "Manual". Fits 0.86" x 1.1" hole. 2-3/4" behind panel depth. NSN: 5930-01-051-1372.

Product Details:
2 Pole, 1 N.O. and 1 N.C., 10 Amp 125v AC maintained push button switch labeled "Douser Open". 125v Neon lamp. Requires 7/8" x 1" hole.

Product Details:
2 Pole, 1 N.O. and 1 N.C., 10 Amp 125v maintained push button lighted switch with Red LED. Operates on 6 to 28 volts DC. Opaque plastic button. Requires 7/8" x 1" hole. Opaque button.

Product Details:
2 Pole, 1 N.O. and 1 N.C., 10 Amp 125v AC momentary push button lighted switch with Green LED. Operates on 6 to 28 volts DC. Opaque plastic button. Requires 7/8" x 1" hole. Opaque button.

Product Details:
Isostat pushbutton switch. SPDT, maintained. 10 amp, 125v. Translucent lens cap. 3" overall length x 1" x 3/4". 0.73" c-c mounting holes. Includes #2341 lamp, 24 - 30v, 1 watt.

Product Details:
Isostat pushbutton switch. 2 poles, N.O., maintained contacts. 10 amp, 125v. 3" overall length x 1" x 3/4". 0.73" c-c mounting holes. Requires #2341 lamp, 24 - 30v, 1 watt - not included.

Product Details:
EAO luminous switch and push cap. DPDT, maintained contact. Red lens. 1.15" x 0.84" hole required. 3-1/2" overall length, 3.25" behind. Requires 2 prong cartridge lamp (not included). Excess from Space Lab.

Product Details:
Dialco Dialight panel mount pushbutton switch. 1P1T, 3 amp, 125 vac. No momentary. Uses 192 series screw-in pushbutton cap. 5/8" diameter body, 1-1/4" behind panel depth. Requires 7/16"D hole. NSN: 5930-01-026-9863.

Product Details:
Microswitch® (a division of Honeywell) socket assembly. 5 amp, 125v. 3/4" x 3/4" x 2-1/8".

Product Details:
"Power On" illuminated pushbutton switch. SPST. 15 amp @ 125/250v AC contact. 6v lamp - lamp is continuously lit with 6v on terminals. 1/4" QC terminals. 2" behind panel depth. Fits 0.850" x 0.850" opening. Same as PL1032-05. CSA and UL listed.

Product Details:
"Power On" illuminated pushbutton switch. DPDT. 10 amp @ 125/250v AC. 6v lamp - lamp is continuously lit with 6v, but one set of contacts could be used to toggle switch light on/off. 1/4" QC terminals. 2" behind panel depth. Fits 0.850" x 0.850" opening. CSA and UL listed.

Product Details:
Micro push switch. "Sold Out" light is on full time, not tied to switch. 5 amp @ 250v AC. Momentary contacts. 28v (10-28v) lamp. 7/8" x 1" hole required. 2-3/8" behind panel depth. CSA, UL.

Product Details:
Micro push switch. "Sold Out" light is on full time, not tied to switch. 5 amp @ 250v AC. Momentary contacts. 28v (10-28v) lamp. 7/8" x 1" hole required. 2-3/8" behind panel depth. CSA, UL.

Product Details:
Dialight momentary lighted pushbutton panel switch. 125v AC, 3 amp, 30v DC, SPDT, 1 position momentary. 5 tab solder lug terminals. Includes 332-0015 cap with lamp, red indicator bar. Includes midget neon bulb - 110v. Fits 3/4" x 3/4" hole. 2-3/8" overall length.

Product Details:
Guardian emergency top pushbutton. 8PDT. 5 amp @ 28v DC or 115v. 400 Hz. 1-5/8" x 1-7/8" x 6-3/8" with button extended. 1.2" mounting center in 8-32 tapped holes on top. NSN: 5930-00-522-3549.

Product Details:
Cuttler-Hammer illuminated pushbutton switch. 2 pole, normally open and normally closed. Maintained contacts - push to switch, push again to switch back. Includes 28v bulb (CM327) to illuminate 3/4" diameter red button. Gold eyelet terminals. Fits 5/8"D hole. 1-3/4" behind panel depth.

Product Details:
EAO snap-action switch. DPDT (2 normally closed & 2 normally closed). 5 amp contacts. Requires 5/8"D opening, 2" behind panel depth. 18mm x 18mm (0.705" x 0.705") bezel. Lens and lamp not included. Lamp max 60v / 1.2w. Use T5.5 lamp. 5/250. 250v, 5 amp.

Product Details:
Alco switch. Also 160 series COMMAND switch. 4PST, 2 normally open, 2 normally closed. 5 amp contacts, 250v AC. 5/8" x 7/8" lens holder. Requires 5/8" mounting hole. Accepts 1.2w, 150v max lamp. Does NOT include lamp or lens.

Product Details:
Vintage electric multiple pushbutton switch. Lamp included. See for patent details and drawings. Circa 1955. Alt. P/N: 604-0421-000.

Product Details:
Microswitch switch assembly. Lens labeled "THRM BAT (A3). Momentary DPDT switch. Use up to 4 midget flange lamps. 2-7/8" overall length. Snaps in to 0.97" x 1.1" hole. NSN: 5930-00-756-5611.

Product Details:
Illuminated keyboard pushbutton switch. Monentary normally open contact. "NEXT" or "PREVIOUS" on video playback. LED is on continously. 0.337" x 0.337" x 0.89" overall height. Alt. P/N: 13BL-090-0020-951.

Product Details:
Dialight red panel indicator. 7 amp. DPDT. Red bar LED illuminates in ON position. Alternate action: Push on / Push off - maintained. 5/8" square x 2.08" overall length. Includes 332-0015 lens. NOTE: LED is on with 5v applied to terminals. User may opt to use normally open contact ON switch in series with LED so it illuminates only when switch is "ON".

Product Details:
Dialight green panel indicator. 7 amp. DPDT. Green bar LED illuminates in ON position. Alternate action: Push on / Push off - maintained. 5/8" square x 2.08" overall length. Includes 332-0025 lens. NOTE: LED is on with 5v applied to terminals. User may opt to use normally open contact ON switch in series with LED so it illuminates only when switch is "ON".

Product Details:
Swann 42 Series push-on / push-off maintained pushbutton switch. SPDT - break before make. 250v AC, 10 amp. 12v blue illuminated pushbutton. 1.45"H x 2.69"L x 0.57"W. Fits 0.46"D hole. 1/4" "QC" spade terminals.

This is a unique pushbutton switch. The manufacturer has a pilot lamp, that illuminates the colored button, that is wired to common and N.O. Contacts. The pilot lamp is 12v DC. The contact is break before make. If you operate a 12v DC multi-pole relay with the NC contact, and use one set of contacts in series with the pilot lamp terminals and a 12v DC source, the lamp will illuminate the button in one position. Then when you change the switch position, because there is a moment between poles when both contacts are open, the pilot voltage does not short. By utilizing the opposite contacts on the relay, you essentially have a maintained switch the will illuminate when on, and go dark when off.

Product Details:
Swann 42 Series push-on / push-off maintained pushbutton switch. SPDT - break before make. 250v AC, 10 amp. 12v green illuminated pushbutton. 1.45"H x 2.69"L x 0.57"W. Fits 0.46"D hole. 1/4" "QC" spade terminals.

This is a unique pushbutton switch. The manufacturer has a pilot lamp, that illuminates the colored button, that is wired to common and N.O. Contacts. The pilot lamp is 12v DC. The contact is break before make. If you operate a 12v DC multi-pole relay with the NC contact, and use one set of contacts in series with the pilot lamp terminals and a 12v DC source, the lamp will illuminate the button in one position. Then when you change the switch position, because there is a moment between poles when both contacts are open, the pilot voltage does not short. By utilizing the opposite contacts on the relay, you essentially have a maintained switch the will illuminate when on, and go dark when off.

Product Details:
Electro Mech momentary back-lit pushbutton switch. SPST, normally open. Requires midget flange lamp (not included). 0.83" x 0.90" x 1.65" overall dimensions.

Product Details:
Clare-Pendar DPDT momentary pushbutton switch. Illuminated white button (0.988"D). 2-1/2" overall length. Requires 0.62"D mounting hole. Requires midget bulb (not included) but available on our site. DC: 7351.

Product Details:
"Press Lite" Marco-Oak illuminated momentary pushbutton. SPDT (one normally open contact, one normally closed contact). White button illuminated no matter which switch position. Includes midget lamp #345 (6v). Fits 1/2"D hole. 2" overall length.

Product Details:
"Press Lite" Marco-Oak illuminated momentary pushbutton. SPDT (one normally open contact, one normally closed contact). Blue button illuminated no matter which switch position. Includes midget lamp #345 (6v). Fits 1/2"D hole. 2" overall length.

Product Details:
Arco Electric orange illuminated switch. SPST. Push on / push off, maintained. 250v AC, 16 amp, 110v lamp. Fits 1"D hole, 1.74" overall length.

Product Details:
Arco Electric green illuminated switch. SPST. Push on / push off, maintained. 250v AC, 16 amp, 110v lamp. Fits 1"D hole, 1.74" overall length.

Product Details:
Arco Electric red illuminated switch. SPST. Push on / push off, maintained. 250v AC, 16 amps, 12v lamp. Fits 1"D hole, 1.74" overall length.

Product Details:
Red keyboard style pushbutton switch. SPST. Normally open. 2 red LEDs illuminate the red button from the back side. 3/4" square, 11/32"H.

Product Details:
Yellow keyboard style pushbutton switch. SPST. Normally open. 2 yellow LEDs illuminate the yellow button from the back side. 3/4" square, 11/32"H.

Product Details:
Dialight backlit SPDT momentary pushbutton switch. 5 amp, 125v contacts. Button labeled "FORM". Snap-in mount. Midget flange lamp holder (not included). 0.628" x 0.628" x 2.26" overall length.

Product Details:
Illuminated momentary pushbutton. SPDT, 10 amp contacts. 28v DC, 1.68 watts. Blank / White 0.91" x 1.58" button...Add your own label. C626 wedge lamp included. Fits < 1" hole.

Product Details:
Green Dim panel lamp test switch. Black anodized 3 solder terminals. NOS-MILSPEC. 1.5"L, 0.46" mounting hole required. Alt p/n: Dialight 801-1030-0332-504. T1 - 3/4". NSN: 6210-00-538-8770. Bulb sold seperatley. www.surplussales.com/Bulbs-Incan-Panel/Bulbs-5.html (midget flange).

Product Details:
Oslo Controls snap-in pushbutton switch. SPST. 250v AC @ 10 amps. Neon backlit. Maintained contact push on / push off. Chrome bezel. Snaps into 7/8" x 1" hole. UL & CSA.

Product Details:
Clare / Pendar aircraft pushbutton switch. DPST maintained. Push-on, push-off contact. 0.73" square red lens. Illuminated with midget bulb like Neon C9A (not included). 0.55" hole required. 2.44" overall length.

Product Details:
Tellite Series 90K pushbutton panel switch. 2PDT, momentary. 9 terminal pins. Two 28v incandescent lamps, midget included. 115 - 250v AC @ 3 amps contact ratings. 50 milliohms @ 6v DC and 100 mA contact resistance, 3 watts max. DC: 7926.

Product Details:
Marco-Oak "Press to Test" aircraft panel lamp holder. Midget flanged, T-1 3/4. Black anodized aluminum body. 3 solder lugs comes with 1 hex nut and lock washer. Brand new in packaging.

Product Details:
Airite Products Inc. prop feather switch. Controlled prop - pitch motor on 1940's - 1960's aircraft. Contacts make and break when knob is pushed or pulled. Lighted knob appears to be 12v. Requires 5/8"D panel opening, 4" behind panel depth. 18 terminals - some strapped, chrome plated, some not. New, unused.

Product Details:
Eaton weapons system Illuminated button. "ARM LW", "CUTTER", "ARMED". DPDT momentary switch. Includes bezel and mounting bracket. Includes 4 midget flange bulbs.

Product Details:
Oslo Controls snap-in pushbutton switch. SPST, normally open. 250v AC @ 10 amps, 1/4 HP @ 125v AC. Series "D" lighted, alternating action, push on, push off. 1/4" quick connect, 4 terminal snap-in panel mount. 12v incandescent lamp. Black case, plastic 1-3/16"L x 15/16"W face, 1.375" total depth.

Product Details:
Oslo Controls snap-in pushbutton switch. SPST, normally open. Series "D" lighted, alternating action, push on, push off. 1/4" quick connect, 4 terminal snap-in panel mount. 12v neon lamp. Black case, plastic 1-3/16"L x 15/16"W face, 1-11/16" total depth.

Product Details:
Jay-El 10 PC console lighted pushbutton switch set.6 x 10648SP14-152 x 10648SP14-332 x 10648SP14-3Waterproof bezel panel mount. 115 VAC / 28 VDC, 1 amp. One position momentary, 2 PDT. 3-1/2" L x 1" W x 1" HT. NOS.

Product Details:
Oslo Controls snap-in pushbutton switch. DPST, normally open. 250v AC @ 10 amps, 1/4 HP @ 125v AC. Series "D" lighted, alternating action, push on, push off. 1/4" quick connect, 6 terminal snap-in panel mount. 125v neon lamp. Black case, plastic 1-3/16"L x 15/16"W face, 1-5/8" total depth.

Product Details:
Oslo Controls snap-in pushbutton switch. SPST, normally open. 250v AC @ 10 amps, 1/4 HP @ 125v AC. Series "D" lighted, alternating action, push on, push off. 1/4" quick connect, 3 terminal snap-in panel mount. 125v neon lamp. Black case, plastic 1-3/16"L x 15/16"W face, 1-5/16" total depth.

Product Details:
Oslo Controls snap-in pushbutton switch. SPST, normally open. 250v AC @ 10 amps, 1/4 HP @ 125v AC. Series "D" lighted, momentary action. 1/4" quick connect, 4 tab, snap-in mount. 12v incandescent lamp. Black case, plastic 1-3/16"L x 15/16"W face, 1-11/16" total depth.

Product Details:
Oslo Controls snap-in pushbutton switch. SPST, normally open. 250v AC @ 10 amps, 1/4 HP @ 125v AC. Series "D" lighted, momentary action. 1/4" quick connect, 3 terminal, snap-in panel mount. 125v neon lamp. Square translucent. Plastic cap with chrome bezel (1" x 1.25"), 15/16" total depth.

Product Details:
Oslo Controls snap-in pushbutton switch. SPST, normally open. 250v AC @ 10 amps, 1/4 HP @ 125v AC. Series "D" lighted, momentary action. 1/4" quick connect, 3 terminal, snap-in panel mount. 125v neon lamp. Black case, plastic 1-3/16"L x 15/16"W face, 1-5/16" total depth.

Product Details:
Micro switch. Red / white / yellow. Holds four lamps (not included). Max 2.4 watts. 2.02"L x 0.69"H x 0.97"W. DC: 8238.

Product Details:
Staco switch indicator module housing. 2 station. Anodized aluminum. 2.85"L x 1.54"W x 0.75"H. 1.93" c-c mounting holes.

Product Details:
Eaton / Safran 4 lamp pushbutton switch housing. (Lamps not included). Gold contact pins x 12. 3" total L x 1" total W x 0.75" total H. Made in the USA. DC: 5/89.

Product Details:
Jay-El two position momentary pushbutton switch. 2P2T, 28v DC. "Paper Advance / Paper Out". Gold plated contact terminals. 2.75"L x 0.75"W x 0.75"H. NOS. Mil-spec. Made in the USA. DC: 3/89.

Product Details:
Vintage Staco lighted pushbutton switch. Aluminum body. 1P1T. 2.4 amp, lamp load @ 28v DC. Push on / Push off. 3 screw terminals. 1.18"D face, 0.364"D actuator, 0.21" actuator height. 1" mounting hole required. Bushing mount. Hardware included. 1.86" total length. NOS.

Product Details:
C&K SPDT keyswitch. Momentary pushbutton with red LED. 125v AC, 0.4 vA max. PCB mount. Red body with black actuator. 0.70"L x 0.48"W x 0.57"H. NOS. Made in the USA.

Product Details:
Staco pushbutton switch. 2P2T, 1 position momentary. Watertight, bushing mounted. 115v AC, 28v DC. 1 amp lamp AC / DC. 6 solder tab. Gold. Black anodized aluminum. 0.44"L bushing, 0.28" actuator height (Red). 0.62" body diameter, 1" body length. NOS. Mil-spec.

Product Details:
Pushbutton tactile switch. Red button, 0.43" square backlit by 4 red LEDs. 0.88"H x 0.587" square body.

Product Details:
Dialco pushbutton switch. SPST, 5 amp, 125 vac/30 vdc, N.O. Momentary, T1-3/4 bulb not included. 5 solder tabs, gold plated. Threaded bushing, anodized aluminum body, plastic base. 0.625" DIA x 1-5/8" L.

Product Details:
Microswitch AML series 21 lighted PB switch. 1PDT Momentary, 125v AC @ 3 amp, 250v AC @ 2 amp. Lamp 28v max, gold contacts, rectangular blue button. 1" L x 5/8" W x 3/8" H. Body - 1.75" L x 1-1/8" W x 0.75" HT. NOS.

Product Details:
Microswitch pushbutton on / off switch. SPDT. AML20 series. Red LED. 8 terminal. 250v AC @ 2 amps, 125v AC @ 3 amps. 5v DC @ 25 mA max. 1.89" total length. 0.79"W x 0.74"H. NOS. DC: 1989.

Product Details:
Microswitch pushbutton on / off switch. SPDT. AML20 series. Yellow LED. 8 terminal. 250v AC @ 2 amps, 125v AC @ 3 amps. 5v DC @ 25 mA max. 1.89" total length. 0.79"W x 0.74"H. NOS. DC: 1989.

Product Details:
Master Specialties twist-lite lamp assembly only. Does not include switch or lens. Fits 0.875" x 1.4" hole. Accomodates 4 independently controlled midget flange lamps. (not included).

Product Details:
Carling pushbutton switch. 20 amp, 125v AC, SPST. Push-on / push off. 0.6" x 1.14", 1.4" behind panel depth. 1/4" spade "QC" terminal. Fits 0.47" hole.

Product Details:
Carling momentary pushbutton switch. 6 amp, 125v, SPST, normally open. Two 5" leads. Molex female pins, 0.07" inside diameter. Fits 0.468" hole.

Product Details:
"Power On" illuminated pushbutton switch. SPST. 15 amp @ 125 / 250v AC contact. 6v lamp - lamp is continuously lit with 6v on terminals. 1/4" QC terminals. 2" behind panel depth. Fits 0.850" x 0.850" opening. Same as PL1032-05. CSA and UL listed.

Product Details:
Dialight pushbutton switch. 30v DC, 3 amp - 125v AC, momentary. Panel bushing mount. Gold plated contacts. Includes white actuator, 0.45"H, 0.48"D. 2" total length, 0.62"D. T 1-3/4 bulb NOT included. NOS. DC: 8451.